DIY Wood Floating Shelf For $10

DIY Wood Floating Shelf For $10

For this week’s project, we made a couple of floating shelves. This DIY Wood Floating Shelf project is a great one for anyone looking to get into woodworking and for the more advanced, alike. It’s very budget friendly, does not take long to make, and they add a nice touch to any wall. Learn how to make your wood floating shelf below! Be sure to download the free plans here, as well. Best of luck on yours.


Tools Needed

Supplies Needed

Approximate Total Cost: $10

The DIY Wood Floating Shelf can be made for about $10 in materials cost. This is the cost for the wood, wood finish, and other basic supplies. *Note: This doesn’t include smaller things you may already have around the shop, including: glue, sandpaper, etc.

Wood Costs

  • 2×4 $3/piece
  • Cedar Pickets $2.50/piece




Cut All of the Wood Pieces

We’ll start this project by marking and making cuts for all of the different pieces for the wood floating shelf. It basically consists of the 2×4 wood frame that screws into the studs in your wall and also the cedar picket shelf box that slides onto the frame. Take a look at the cut list in the free plans for dimensions and guidance. Sand the boards, once they’re cut to size.

cutting-frame-wood-floating-shelves

cutting-boards-wood-floating-shelves

Start Assembly, Making the Frame First

Once you have all of your pieces, we’ll make the 2×4 wood frame that’ll screw into the wall. Kreg Jig (pocket hole joinery) the short boards onto the longer board. Also screw in 3” wood screws from the opposite side, for more security. This frame will be completely hidden on the inside of the cedar shelf box, so once it’s made there is no need to finish this. You can leave it all rough.

frame-wood-floating-shelves

kreg-jig-wood-floating-shelves

Assemble the Cedar Box Shelf

Then we’ll put together the cedar box that will slide over the 2×4 frame, becoming the main shelf and the most visible part of this project. Dry fit all of the pieces to make sure your cuts were accurate, then add wood glue to the joints. Nail everything together with 1 ¼” nails and then let the glue dry.

Enter your email below and I'll instantly send you 60 free woodworking plans to the most popular projects on my page!

We respect your email privacy and your information is never shared

The free plans will be instantly sent to the email address you submit above.

cedar-shelf-2-wood-floating-shelves

Sand, Finish, and Let Cure

Sand the cedar box down to at least 220 grit with your orbital sander. The finishing process that I did for this project was the steel wool and vinegar solution/stain. Refer to this tutorial video here. Let your solution work its magic for a while and once to the desired color, seal it all up with a water-based spray polyurethane. The water-based sealer ensures that you won’t change the effect, patina, and color of the steel wool and vinegar solution.

cedar-steel-wool-vinegar-wood-floating-shelves

Install the 2×4 Frame and the Cedar Shelf

Once the finishing process is done and everything has dried to the manufacturer’s recommended time, we can install it! We’ll first find the studs in the wall, should be about 16” apart. Then we’ll screw the 2×4 frame into the wall with 2 3” wood screws for each connection to the stud. Slide the cedar box shelf on and you’re done!

*Note: If you’re wanting a more secure shelf (maybe the kids could pull the shelf off of the frame) you can simply screw the shelf onto the 2×4 frame from the underside or topside.

attaching-shelf-wood-floating-shelves

You’ve done the work, now reap the benefits of your DIY Wood Floating Shelf or Shelves, in my case. Add what you want to them and share this project with your friends. Thanks for following along.

wood-floating-shelves-final-2

Get the plans & designs for 500 best selling wood crafts

3 Comments

    Annelise

    What would the weight limit be for these shelves? I would like to make some to use to hold books.

    Linda Leuty

    Very cool shevles

    Matt

    No need for a kreg jig just glue and screw through the face of the 2×4.

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*